 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| HIGH CMR, 10 Mbps TOTEM POLE OUTPUT TYPE 5-PIN SOP PHOTOCOUPLER FEATURES * HIGH COMMON MODE TRANSIENT IMMUNITY CMH, CML = 20 kV/s TYP * SMALL AND THIN PACKAGE 5-pin SOP * HIGH SPEED 10 Mbps * PULSE WIDTH DISTORTION |tPHL - tPLH| = 7 ns TYP * HIGH ISOLATION VOLTAGE BV = 2500 Vr.m.s. * TOTEM POLE OUTPUT No pull-up resistor required * AVAILABLE IN TAPE AND REEL PS9715-F3, F4: 3500 pcs/reel PS9715 DESCRIPTION PS9715 is an optically coupled high-speed, totem pole output isolator containing a GaAIAs LED on the light emitting side (input side) and a photodiode and a signal processing circuit on the light receiving side (output side) on one chip. APPLICATIONS * LAN/FA * MEASUREMENT EQUIPMENT * PDP PS9715 6 5 4 1 3 ELECTRICAL CHARACTERISTICS (TA = 0 to +85C, Unless otherwise specified) PART NUMBER SYMBOL PARAMETERS Forward Voltage, IF = 10 mA, TA = 25C Reverse Current, VR = 3 V, TA = 25C Capacitance, V = 0, f = 1 MHz, TA = 25C High Level Output Current2 Vcc = VO = 5.5 V, VF = 0.8 V High Level Output Voltage Vcc = 4.5 V, IF = 250 A, IOH = -2 mA Low Level Output Voltage Vcc = 4.5 V, VF = 0.8 V, IOL = 8 mA High Level Supply Current, VCC = 5.5 V, IF = 0 mA Low Level Supply Current, VCC = 5.5 V, IF = 10 mA High Level Output Short Circuit Current, VCC = 5.5 V, VO = GND IF = 0 mA, 10 ms or less Low Level Output Short Circuit Current, VCC = 5.5 V, VO = GND IF = 8 mA, 10 ms or less Threshhold Input Current, High Low, VCC = 5 V TA = 25C UNITS V A pF A V V mA mA mA mA mA pF ns ns 15 10 15 10 1011 0.4 33 40 65 85 65 85 2.4 30 0.003 3.0 0.25 12 13 -26 34 2.3 5 6 0.6 17 18 200 MIN 1.4 VF IR Ct IOH VOH PS9715 TYP1 1.65 MAX 1.9 10 Diode Detector VOL ICCH ICCL IOSH IOSL IFHL RI-O CI-O tPHL tPLH Coupled Isolation Resistance, VI-O = 1 k VDC, RH = 40 to 60%, TA = 25C Isolation Capacitance, V = 0, f = 1 MHz, TA = 25C Propagation Delay Time , High Low VCC = 5 V, IF = 7.5 mA Propagation Delay Time1, Low High VCC = 5 V, IF = 7.5 mA 1 TA = 25C TA = 25C Continued on next page California Eastern Laboratories PS9715 ELECTRICAL CHARACTERISTICS (TA = 0 to +85C, Unless otherwise specified), Continued PART NUMBER SYMBOL | tPHL - tPLH | CMH CML PARAMETERS Pulse Width Distortion, (PWD)3, VCC = 5 V, IF = 7.5 mA Common Mode Transient Immunity at High Level VCC = 5 V, TA = 25C, IF = 0 mA, VO (MIN) = 2 V, VCM = 1 kV Common Mode Transient Immunity at Low Level Output4, VCC = 5 V, TA = 25C, IF = 7.5 mA, VO (MAX) = 0.8 V, VCM = 1 kV Output4, UNITS ns kV/s kV/s 10 10 MIN PS9715 TYP 7 20 20 MAX 50 Notes: 1. Typical values at TA = 25C. 2. Because a high level output current (IOH) of 300 A or more may be output when the temperature is 0C or less and when VCC is around 3 to 4 V, it is important to confirm the characteristics (operation with the power supply on and off) during design, before using the device. 3. Test Circuit for Propagation delay time VCC = 5 V VCC = 5 V IF (ON) Pulse input (IF) Input VO (monitor) 50% IF (ON) 1.3 k (PW = 500 ns, Duty cycle = 1/2) 0.1 F VOH Input (monitor) 47 CL = 30 pF Output 2.5 k tPHL tPLH 1.5 V VOL Coupled CL includes probe and stray wiring capacitance. 4.Test Circuit for common mode transient immunity SW IF VCC = 5 V 0.1 F VO (Monitor) CL = 15 pF VCM VO (IF = 7.5 mA) 10% tr VO (IF = 0 mA) tf VOH 2V 0.8 V VOL 0V VCM 90% 1 kV CL includes probe and stray wiring capacitance. USAGE CAUTIONS 1. This device is ESD sensitive. 2. Bypass capacitor of more than 0.1 F is used between VCC and GND near device. Also, ensure that the distance between the leads of the photocoupler and capactor is no more than 10 mm. ABSOLUTE MAXIMUM RATINGS1 (TA = 25C) SYMBOLS Diode IF VR Detector VCC VO IOH IOL PC Coupled BV TOP TSTG PARAMETERS Forward Current Reverse Voltage Supply Voltage Output Voltage High level Output Current2 Low level Output Current2 Power Dissipation2,3 Isolation Voltage4 Operating Temperature Storage Temperature UNITS mA V V V mA mA mW Vr.m.s. C C RATINGS 30 5 7 7 -5 13 130 2500 -40 to +85 -55 to +125 RECOMMENDED OPERATING CONDITIONS PART NUMBER SYMBOLS IFH IFL VCC N TA PARAMETERS High Level Input Current Low Level Input Current Supply Voltage TTL(loads) Operating Temperature PS9715 UNITS MIN TYP MAX mA 7.5 12.5 A 0 250 V 4.5 5.0 5.5 3 C 0 +85 Notes: 1. Operation in excess of any one of these parameters may result in permanent damage. 2. TA = -40 to +85C, Applies to output pin Vo and power supply pin VCC. 4. AC voltage for 1 minute at TA = 25 C, RH = 60% between input and output. PS9715 TYPICAL PERFORMANCE CURVES (TA = 25C) MAXIMUM FORWARD CURRENT vs. AMBIENT TEMPERATURE 40 150 DETECTOR POWER DISSIPATION vs. AMBIENT TEMPERATURE Maximum Forward Current, IF (mA) 30 Detector Power Dissipation, PC (mW 80 85 100 20 50 10 0 20 40 60 100 0 20 40 60 80 85 100 Ambient Temperature, TA (C) FORWARD CURRENT vs. FORWARD VOLTAGE 100 Ambient Temperature, TA (C) SUPPLY CURRENT vs. AMBIENT TEMPERATURE 20 High Level Supply Current, ICCH (mA) LowLevel Supply Current, ICCL (mA) VCC = 5.5 V 16 ICCL (IF = 10 mA) 12 ICCH (IF = 0 mA) 8 Forward Curren, IF (mA) 10 TA = +85C +50C 1 +25C 0C -25C 0.1 4 0.01 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 0 -50 -25 0 25 50 75 100 Forward Voltage, VF (V) Ambient Temperature, TA (C) HIGH LEVEL OUTPUT VOLTAGE vs. AMBIENT TEMPERATURE 5 VCC = 4.5 V, VF = 0.8 V, IOH = 2.0 mA 4 PROPAGATION DELAY TIME, PULSE WIDTH DISTORTION vs. AMBIENT TEMPERATURE Propagation Delay Time,tPHL, tPLH (ns) Pulse Width Distortion, |tPHL--tPLH| (ns) 50 tPLH 40 tPHL High Level Output Voltage, VOH (V) 3 30 2 20 1 10 PWD 0 -50 0 -50 -25 0 25 50 75 100 -25 0 25 50 75 100 Ambient Temperature, TA (C) Ambient Temperature, TA (C) PS9715 TYPICAL PERFORMANCE CURVES (TA = 25C) LOW LEVEL OUTPUT VOLTAGE vs. AMBIENT TEMPERATURE 0.5 5 LOW LEVEL OUTPUT VOLTAGE vs. AMBIENT TEMPERATURE Low Level Output Voltage, VOL (V) Low Level Output Voltage, VOL (V) VCC = 4.5 V, IF = 7.5 mA, IOL = 8.0 mA VCC = 5.0 V 4 0.4 0.3 3 0.2 2 0.1 1 0 -50 0 -25 0 25 50 75 100 -50 -25 0 25 50 75 100 Ambient Temperature, TA (C) Ambient Temperature, TA (C) LOW LEVEL OUTPUT VOLTAGE vs. LOW LEVEL OUTPUT CURRENT 0.5 HIGHLEVEL OUTPUT VOLTAGE vs. HIGHLEVEL OUTPUT CURRENT 5 Low Level Output Voltage, VOL (V) High Level Output Voltage, VOH (V) VCC = 4.5 V, IF = 5.0 mA 0.4 TA = 85C 0C 0.3 25C TA = 85C 4 25C 0C VCC = 4.5 V, VF = 0.8 V 3 0.2 2 0.1 1 0 2.5 5 7.5 10 12.5 13 0 -1 -2 -3 -4 -5 Low Level OututCurrent, IOL (mA) High Level OututCurrent, IOH (mA) HIGH LEVEL OUTPUT VOLTAGE vs. HIGH LEVEL OUTPUT CURRENT 4 PROPAGATION DELAY TIME, PULSE WIDTH DISTORTION vs. FORWARD CURRENT 60 High Level Output Voltage, VOH (V) TA = 85C 25C 3 0C VCC = 4.5 V, IF = 250 A Propagation Delay Time,tPHL, tPLH (ns) Pulse Width Distortion, |tPHL--tPLH| (ns) TA = 25C, VCC = 5 V tPHL 40 2 tPLH 20 PWD 1 0 -5 -10 -15 -20 -25 -30 -35 0 5 10 15 20 25 30 High Level OututCurrent, IOH (mA) Forward Current, IF (mA) PS9715 OUTLINE DIMENSIONS (Units in mm) PS9715 4.00.5 MARKING TOP VIEW 5 4 3 1. Anode 2. Cathode 3. GND 4. VO 5. VCC 1 2 7.00.3 4.4 No. 1 pin Mark 9715 N003 Assembly Lot N 0 03 2.10.2 0.15 +0.10 -0.05 Week Assembled Year Assembled (Last 1 Digit) Rank Code 0.10.1 1.27 0.4 +0.10 -0.05 0.25 M 0.50.3 TAPING SPECIFICATIONS (Units in mm) TAPE OUTLINE AND DIMENSIONS 4.00.1 2.9 MAX 2.00.05 1.5 -0 +0.1 REEL OUTLINE AND DIMENSIONS 2.00.5 1.5 0.1 1.750.1 2.00.5 13.00.2 3302.0 120.2 7.40.1 R1.0 21.00.8 13.00.2 1001.0 5.50.05 13.51.0 1.550.1 4.60.1 80.1 0.3 2.40.1 17.51.0 11.9 to 15.4 Outer edge of flange Packing : 3500 pcs/reel TAPE DIRECTION PS9715-F3 PS9715-F4 PS9715 RECOMMENDED SOLDERING CONDITIONS (1) Infrared reflow soldering * Peak reflow temperature * Time of temperature higher than 210 C * Number of reflows * Flux 235C or below (package surface temperature) 30 seconds or less Three Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt % is recommended.) Package Surface Temperature T (C) (heating) to 10 s 235C (peak temperature) 210C to 30 s 100 to 160C 60 to 120 s s (preheating) Time (s) (3) Cautions * Fluxes Avoid removing the residual flux with freon-based and chlorine-based cleaning solvent. Life Support Applications These NEC products are not intended for use in life support devices, appliances, or systems where the malfunction of these products can reasonably be expected to result in personal injury. The customers of CEL using or selling these products for use in such applications do so at their own risk and agree to fully indemnify CEL for all damages resulting from such improper use or sale. EXCLUSIVE NORTH AMERICAN AGENT FOR NEC RF, MICROWAVE & OPTOELECTRONIC SEMICONDUCTORS CALIFORNIA EASTERN LABORATORIES * Headquarters * 4590 Patrick Henry Drive * Santa Clara, CA 95054-1817 * (408) 988-3500 * Telex 34-6393 * FAX (408) 988-0279 Internet: http://WWW.CEL.COM DATA SUBJECT TO CHANGE WITHOUT NOTICE 06/26/2002 |
Price & Availability of PS9715
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |